Brand name of the company that manufactures the device.
Model name of the device.
Information about the width, i.e. the horizontal side of the device when it is used in its standard orientation.
|62 mm (millimeters)|
6.2 cm (centimeters)
0.203 ft (feet)
2.441 in (inches)
Information about the height, i.e. the vertical side of the device when it is used in its standard orientation.
|135 mm (millimeters)|
13.5 cm (centimeters)
0.443 ft (feet)
5.315 in (inches)
Information about the thickness/depth of the device in different measurement units.
|10 mm (millimeters)|
1 cm (centimeters)
0.033 ft (feet)
0.394 in (inches)
Information about the weight of the device in different measurement units.
|145 g (grams)|
0.32 lbs (pounds)
5.11 oz (ounces)
Estimated volume of the device, calculated from the dimensions provided by the manufacturer. Applies for devices in the form of a rectangular parallelepiped.
|83.7 cm³ (cubic centimeters)|
5.08 in³ (cubic inches)
Information about the colors, in which the device is available in the market.
Materials used in the fabrication of the device's body.
|SIM card type|
Information about the type and size (form factor) of the SIM card used in the device.
|Mini-SIM (2FF - second form factor, since late 1990s, 25.00 x 15.00 x 0.76 mm)|
Micro-SIM (3FF - third form factor, since 2003, 15.00 x 12.00 x 0.76 mm)
|Number of SIM cards|
Information about the number of SIM cards, supported by the device.
Information about some specific features related to the SIM card(s) of the device.
|Dual SIM stand-by (Both cards are active. When one is busy, the other is not active)|
GSM (Global System for Mobile Communications) was developed to replace the analog cellular network (1G), therefore it is referred to as a 2G mobile network. It has been improved with the addition of General Packet Radio Services (GPRS) and later via the Enhanced Data rates for GSM Evolution (EDGE) technology.
|GSM 850 MHz|
GSM 900 MHz
GSM 1800 MHz
GSM 1900 MHz
W-CDMA (Wideband Code Division Multiple Access) is an air interface used by 3G mobile networks. It is one of the three different UMTS interfaces together with the TD-SCDMA and the TD-CDMA. The standard provides faster data transfer speeds and allows more users to connect to the network simultaneously.
|W-CDMA 850 MHz|
W-CDMA 2100 MHz
|Mobile network technologies|
There are several network technologies that enhance the performance of mobile networks mainly by increased data bandwidth. Information about the communication technologies supported by the device and their respective uplink and downlink bandwidth.
|UMTS (384 kbit/s )|
|Operating system (OS)|
Information about the operating system used by the device as well as its version.
|Android 4.4.2 KitKat|
The SoC integrates different hardware components such as the CPU, GPU, memory, peripherals, interfaces, etc., as well as software for their functioning.
Information about the process technology used in manufacturing the chip. The value in nanometers represents half the distance between elements that make up the CPU.
|28 nm (nanometers)|
CPU is the Central Processing Unit or the processor of a mobile device. Its main function is to interpret and execute instructions contained in software applications.
The CPU bits are determined by the bit-size of the processor registers, address buses and data buses. 64-bit CPUs provide better performance than 32-bit ones, which on their part perform better than 16-bit processors.
The instruction set architecture (ISA) is a set of commands used by the software to manage the CPU's work. Information about the set of instructions the processor can execute.
|Level 1 cache memory (L1)|
The cache memory is used by the processor in order to shorten the time needed to access data and instructions that a frequently used. The L1 (level 1) cache memory has a small volume, but operates faster than the RAM and the rest cache memory levels. If the processor does not find the data needed in L1, it continues to look for it in the L2 cache memory. In some processors the search in L1 and L2 is simultaneous.
|32 KB + 32 KB (kilobytes)|
|Level 2 cache memory (L2)|
The L2 (level 2) cache memory is slower than L1, but has a larger capacity, instead, which allows it to cache more data. Just like L1, it is much faster than the system memory (RAM). If the CPU does not find the data needed in L2, it proceeds to look for them in the L3 cache memory (if there is such) or in the RAM.
|256 KB (kilobytes)|
0.25 MB (megabytes)
A CPU core is the processor unit, which executes software instructions. Presently, besides single-core processors, there are dual-core, quad-core, hexa-core and so on multi-core processors. They increase the performance of the device allowing the execution of multiple instructions in parallel.
The frequency of the processor describes its clock rate in cycles per second. It is measured in Megahertz (MHz) or Gigahertz (GHz).
|1200 MHz (megahertz)|
GPU is a graphical processing unit, which handles computation for 2D/3D graphics applications. In mobile devices GPU is usually utilized by games, UI, video playback, etc. GPU can also perform computation in applications traditionally handled by the CPU.
|ARM Mali-400 MP1|
Similar to the CPU, the GPU consists of processing units called cores. They handle the computation of graphics in various applications.
The frequency is the clock rate of the graphic processor (GPU), which is measured in Megahertz (MHz) or Gigahertz (GHz).
|500 MHz (megahertz)|
RAM (Random-Access Memory) is used by the operating system and all installed applications. Data in the RAM is lost after the device is turned off or restarted.
|1 GB (gigabytes)|
Information about the type of RAM used by the device.
RAM frequency relates directly to the rate of reading/writing from/in the RAM memory.
|266 MHz (megahertz)|
Information about the capacity of the built-in storage of the device. Sometimes one and the same model may is offered in variants with different internal storage capacity.
|4 GB (gigabytes)|
The various types of memory cards are characterized by different sizes and capacity. Information about the supported types of memory cards.
One of the main characteristics of the display is its type/technology, on which depends its performance.
In mobile devices display size is represented by the length of its diagonal measured in inches.
|4.5 in (inches)|
114.3 mm (millimeters)
11.43 cm (centimeters)
Approximate width of the display
|2.2 in (inches)|
56 mm (millimeters)
5.6 cm (centimeters)
Approximate height of the display
|3.92 in (inches)|
99.64 mm (millimeters)
9.96 cm (centimeters)
The ratio between the long and the short side of the display
The display resolution shows the number of pixels on the horizontal and vertical side of the screen. The higher the resolution is, the greater the detail of the displayed content.
|480 x 854 pixels|
Information about the number of pixels per centimeter (ppcm) or per inch (ppi) of the display. The higher the pixel density, the more detailed and clearer is the information displayed on the screen.
|218 ppi (pixels per inch)|
85 ppcm (pixels per centimeter)
The color depth of the display is also known as bit depth. It shows the number of bits used for the color components of one pixel. Information about the maximum number of colors the screen can display.
The estimated percentage of the screen area from the device's front area.
|66.88 % (percent)|
Information about other functions and features of the display.
Sensors vary in type and purpose. They increase the overall functionality of the device, in which they are integrated.
Information about the manufacturer and model of the image sensor used by this camera of the device.
Information about the sensor type of the camera. Some of the most widely used types of image sensors on mobile devices are CMOS, BSI, ISOCELL, etc.
|CMOS (complementary metal-oxide semiconductor)|
Information about the dimensions of the image sensor used in the device. Usually cameras with larger sensors and less pixel density tend to provide better image quality despite the lower resolution.
|2.8 x 2.1 mm (millimeters)|
0.14 in (inches)
Pixels are usually measured in microns (μm). Larger ones are capable of recording more light, hence, will offer better low light shooting and wider dynamic range compared to the smaller pixels. On the other hand, smaller pixels allow for increasing the resolution while preserving the same sensor size.
|1.75 µm (micrometers)|
0.001750 mm (millimeters)
Crop factor is the ratio of the dimensions of a full frame camera's sensor (36 x 24 mm, which equals the frame size of a 35 mm film) and the dimensions of the image sensor of the device. The number shown is the ratio between the diagonals of a full frame sensor (43.3 mm) and the sensor in question.
The aperture (f-stop number) indicates the size of the lens diaphragm opening, which controls the amount of light reaching the image sensor. The lower the f-stop number, the larger the diaphragm opening is, hence, the more light reaches the sensor. Usually, the f-stop number specified is the one that corresponds to the maximum possible diaphragm opening.
The rear cameras of mobile devices use mainly a LED flash. It may arrive in a single, dual- or multi-light setup and in different arrangements.
One of the main characteristics of the cameras is their image resolution. It states the number of pixels on the horizontal and vertical dimensions of the image, which can also be shown in megapixels that indicate the approximate number of pixels in millions.
|1600 x 1200 pixels|
1.92 MP (megapixels)
Information about the maximum resolution at which the rear camera can shoot videos.
|800 x 480 pixels|
0.38 MP (megapixels)
Information about additional software and hardware features of the rear camera which improve its overall performance.
Information about the number of pixels on the horizontal and vertical dimensions of the photos taken by the front camera, indicated in megapixels as well.
|1600 x 1200 pixels|
1.92 MP (megapixels)
Information about the maximum resolution of the videos shot by the front camera.
|640 x 480 pixels|
0.31 MP (megapixels)
The loudspeaker is a device, which reproduces various sounds such as ring tones, alarms, music, voice calls, etc. Information about the type of speakers the device uses.
Information whether the device has an FM radio receiver or not.
The tracking/positioning service is provided by various satellite navigation systems, which track the autonomous geo-spatial positioning of the device that supports them. The most common satellite navigation systems are the GPS and the GLONASS. There are also non-satellite technologies for locating mobile devices such as the Enhanced Observed Time Difference, Enhanced 911, GSM Cell ID.
Wi-Fi communication between devices is realized via the IEEE 802.11 standards. Some devices have the possibility to serve as Wi-Fi Hotspots by providing internet access for other nearby devices. Wi-Fi Direct (Wi-Fi P2P) is another useful standard that allows devices to communicate with each other without the need for wireless access point (WAP).
|802.11b (IEEE 802.11b-1999)|
802.11g (IEEE 802.11g-2003)
802.11n (IEEE 802.11n-2009)
The technology has several versions, which improve the connection speed, range, connectivity and discoverability of the devices. Information about the Bluetooth version of the device.
Bluetooth uses various profiles and protocols related to faster exchange of data, energy saving, better device discoverability, etc. Some of those supported by the device are listed here.
|A2DP (Advanced Audio Distribution Profile)|
There are several USB connector types: the Standard one, the Mini and Micro connectors, On-The-Go connectors, etc. Type of the USB connector used by the device.
There are several versions of the Universal Serial Bus (USB) standard: USB 1.0 (1996), the USB 2.0 (2000), the USB 3.0 (2008), etc. With each following version the rate of data transfer is increased.
Тhe USB interface in mobile devices may be used for different purposes such as battery charging, using the device as a mass storage, host, etc.
Information whether the device is equipped with a 3.5 mm audio jack.
Information about some of the most widely used connectivity technologies supported by the device.
Information about some of the features and standards supported by the browser of the device.
|Audio file formats/codecs|
List of some of the most common audio file formats and codecs supported standardly by the device.
|AAC (Advanced Audio Coding)|
eAAC+ / aacPlus v2 / HE-AAC v2
MP3 (MPEG-2 Audio Layer II, .mp3)
WMA (Windows Media Audio, .wma)
WAV (Waveform Audio File Format, .wav, .wave)
|Video file formats/codecs|
List of some of the most common video file formats and codecs supported standardly by the device.
|3GPP (3rd Generation Partnership Project, .3gp)|
The capacity of a battery shows the maximum charge, which it can store, measured in mili-Ampere hours.
|1400 mAh (milliampere-hours)|
The battery type is determined by its structure and more specifically, by the chemicals used in it. There are different battery types and some of the most commonly used in mobile devices are the lithium-ion (Li-Ion) and the lithium-ion polymer battery (Li-Polymer).
|2G talk time|
2G talk time is the time period a battery charge will last, if one is constantly talking on the phone in a 2G cellular network.
|6 h (hours)|
360 min (minutes)
|2G stand-by time|
2G stand-by time is the longest time a battery charge will last, if the device is not used but is constantly connected to the 2G cellular network.
|180 h (hours)|
10800 min (minutes)
|3G talk time|
3G talk time is the time period a battery charge will last, if one is constantly talking on the phone in a 3G cellular network.
|6 h (hours)|
360 min (minutes)
|3G stand-by time|
3G stand-by time is the longest time a battery charge will last, if the device is not used but is constantly connected to the 3G mobile network.
|180 h (hours)|
10800 min (minutes)
Information about some additional features of the device's battery.