Brand name of the company that manufactures the device.
Model name of the device.
Information about the width, i.e. the horizontal side of the device when it is used in its standard orientation.
|74.2 mm (millimeters)|
7.42 cm (centimeters)
0.243 ft (feet)
2.921 in (inches)
Information about the height, i.e. the vertical side of the device when it is used in its standard orientation.
|160.8 mm (millimeters)|
16.08 cm (centimeters)
0.528 ft (feet)
6.331 in (inches)
Information about the thickness/depth of the device in different measurement units.
|8.2 mm (millimeters)|
0.82 cm (centimeters)
0.027 ft (feet)
0.323 in (inches)
Estimated volume of the device, calculated from the dimensions provided by the manufacturer. Applies for devices in the form of a rectangular parallelepiped.
|97.84 cm³ (cubic centimeters)|
5.94 in³ (cubic inches)
Information about the colors, in which the device is available in the market.
Materials used in the fabrication of the device's body.
|SIM card type|
Information about the type and size (form factor) of the SIM card used in the device.
|Nano-SIM (4FF - fourth form factor, since 2012, 12.30 x 8.80 x 0.67 mm)|
|Number of SIM cards|
Information about the number of SIM cards, supported by the device.
Information about some specific features related to the SIM card(s) of the device.
|Dual SIM stand-by (Both cards are active. When one is busy, the other is not active)|
GSM (Global System for Mobile Communications) was developed to replace the analog cellular network (1G), therefore it is referred to as a 2G mobile network. It has been improved with the addition of General Packet Radio Services (GPRS) and later via the Enhanced Data rates for GSM Evolution (EDGE) technology.
|GSM 850 MHz (B5)|
GSM 900 MHz (B8)
GSM 1800 MHz (B3)
GSM 1900 MHz (B2)
UMTS stands for Universal Mobile Telecommunications System. Based on the GSM standard, it is deemed as a 3G mobile network standard. It has been developed by the 3GPP and its major advantage is the provision of greater bandwidth and spectral efficiency, due to the W-CDMA technology.
|UMTS 850 MHz (B5)|
UMTS 900 MHz (B8)
UMTS 1900 MHz (B2)
UMTS 2100 MHz (B1)
LTE is deemed to be the fourth generation (4G) of mobile communications technology. It has been developed by the 3GPP based on the GSM/EDGE and UMTS/HSPA technologies in order to increase the speed and capacity of wireless data networks. A further development of the technology is called LTE Advanced.
|LTE-FDD 700 MHz (B12)|
LTE-FDD 700 MHz (B17)
LTE-FDD 700 MHz (B28)
LTE-FDD 800 MHz (B20)
LTE-FDD 850 MHz (B5)
LTE-FDD 900 MHz (B8)
LTE-FDD 1700 MHz (B4)
LTE-FDD 1700 MHz (B66)
LTE-FDD 1800 MHz (B3)
LTE-FDD 1900 MHz (B2)
LTE-FDD 2100 MHz (B1)
LTE-FDD 2600 MHz (B7)
LTE-TDD 1900 MHz (B39)
LTE-TDD 2000 MHz (B34)
LTE-TDD 2300 MHz (B40)
LTE-TDD 2500 MHz (B41)
LTE-TDD 2600 MHz (B38)
The 5G (fifth generation) mobile networks use the new radio access technology (RAT) developed by 3GPP, dubbed 5G NR and deemed as the global standard for the air interface of 5G networks. 5G NR operates in two frequency ranges - FR1 (sub-6 GHz) and FR2 (above 24 GHz). In the FR1 frequency range, the 5G mobile networks use a number of bands, some of which are traditionally used by previous standards. The FR2 provides shorter range but higher available bandwidth than bands in the FR1.
|5G-FDD 700 MHz (n28)|
5G-FDD 800 MHz (n20)
5G-FDD 850 MHz (n5)
5G-FDD 900 MHz (n8)
5G-FDD 1800 MHz (n3)
5G-FDD 2100 MHz (n1)
5G-TDD 2500 MHz (n41)
5G-FDD 2600 MHz (n7)
5G-TDD 2600 MHz (n38)
5G-TDD 3500 MHz (n78)
|Mobile network technologies|
There are several network technologies that enhance the performance of mobile networks mainly by increased data bandwidth. Information about the communication technologies supported by the device and their respective uplink and downlink bandwidth.
|UMTS (384 kbit/s )|
HSPA+ (HSUPA 5.76 Mbit/s , HSDPA 42 Mbit/s )
|Operating system (OS)|
Information about the operating system used by the device as well as its version.
|User interface (UI)|
Name and version of the user interface (UI) used by the operating system (OS).
The SoC integrates different hardware components such as the CPU, GPU, memory, peripherals, interfaces, etc., as well as software for their functioning.
|MediaTek Dimensity 920 (MT6879)|
Information about the process technology used in manufacturing the chip. The value in nanometers represents half the distance between elements that make up the CPU.
|6 nm (nanometers)|
CPU is the Central Processing Unit or the processor of a mobile device. Its main function is to interpret and execute instructions contained in software applications.
|2x 2.5 GHz ARM Cortex-A78, 6x 2.0 GHz ARM Cortex-A55|
The CPU bits are determined by the bit-size of the processor registers, address buses and data buses. 64-bit CPUs provide better performance than 32-bit ones, which on their part perform better than 16-bit processors.
The instruction set architecture (ISA) is a set of commands used by the software to manage the CPU's work. Information about the set of instructions the processor can execute.
|Level 3 cache memory (L3)|
The L3 (level 3) cache memory is slower than L2, but has a larger capacity, instead, which allows it to cache more data. Just like L2, it is much faster than the system memory (RAM).
|2 KB (kilobytes)|
0.00195312 MB (megabytes)
A CPU core is the processor unit, which executes software instructions. Presently, besides single-core processors, there are dual-core, quad-core, hexa-core and so on multi-core processors. They increase the performance of the device allowing the execution of multiple instructions in parallel.
The frequency of the processor describes its clock rate in cycles per second. It is measured in Megahertz (MHz) or Gigahertz (GHz).
|2500 MHz (megahertz)|
GPU is a graphical processing unit, which handles computation for 2D/3D graphics applications. In mobile devices GPU is usually utilized by games, UI, video playback, etc. GPU can also perform computation in applications traditionally handled by the CPU.
|ARM Mali-G68 MC4|
Similar to the CPU, the GPU consists of processing units called cores. They handle the computation of graphics in various applications.
RAM (Random-Access Memory) is used by the operating system and all installed applications. Data in the RAM is lost after the device is turned off or restarted.
|6 GB (gigabytes)|
8 GB (gigabytes)
Information about the capacity of the built-in storage of the device. Sometimes one and the same model may is offered in variants with different internal storage capacity.
|128 GB (gigabytes)|
256 GB (gigabytes)
One of the main characteristics of the display is its type/technology, on which depends its performance.
In mobile devices display size is represented by the length of its diagonal measured in inches.
|6.5 in (inches)|
165.1 mm (millimeters)
16.51 cm (centimeters)
Approximate width of the display
|2.67 in (inches)|
67.75 mm (millimeters)
6.78 cm (centimeters)
Approximate height of the display
|5.93 in (inches)|
150.56 mm (millimeters)
15.06 cm (centimeters)
The ratio between the long and the short side of the display
The display resolution shows the number of pixels on the horizontal and vertical side of the screen. The higher the resolution is, the greater the detail of the displayed content.
|1080 x 2400 pixels|
Information about the number of pixels per centimeter (ppcm) or per inch (ppi) of the display. The higher the pixel density, the more detailed and clearer is the information displayed on the screen.
|405 ppi (pixels per inch)|
159 ppcm (pixels per centimeter)
The color depth of the display is also known as bit depth. It shows the number of bits used for the color components of one pixel. Information about the maximum number of colors the screen can display.
The estimated percentage of the screen area from the device's front area.
|85.77 % (percent)|
Information about other functions and features of the display.
|2.5D curved glass screen|
Corning Gorilla Glass 3
144 Hz refresh rate
10-bit color bit depth
500 cd/m² typical brightness
700 cd/m² HBM
Sensors vary in type and purpose. They increase the overall functionality of the device, in which they are integrated.
|Side-mounted fingerprint sensor|
Information about the manufacturer and model of the image sensor used by this camera of the device.
Information about the sensor type of the camera. Some of the most widely used types of image sensors on mobile devices are CMOS, BSI, ISOCELL, etc.
The optical format of an image sensor is an indication of its shape and size. It is usually expressed in inches.
Pixels are usually measured in microns (μm). Larger ones are capable of recording more light, hence, will offer better low light shooting and wider dynamic range compared to the smaller pixels. On the other hand, smaller pixels allow for increasing the resolution while preserving the same sensor size.
|1 µm (micrometers)|
0.001000 mm (millimeters)
The aperture (f-stop number) indicates the size of the lens diaphragm opening, which controls the amount of light reaching the image sensor. The lower the f-stop number, the larger the diaphragm opening is, hence, the more light reaches the sensor. Usually, the f-stop number specified is the one that corresponds to the maximum possible diaphragm opening.
The rear cameras of mobile devices use mainly a LED flash. It may arrive in a single, dual- or multi-light setup and in different arrangements.
One of the main characteristics of the cameras is their image resolution. It states the number of pixels on the horizontal and vertical dimensions of the image, which can also be shown in megapixels that indicate the approximate number of pixels in millions.
|50 MP (megapixels)|
Information about the maximum resolution at which the rear camera can shoot videos.
|7680 x 4320 pixels|
33.18 MP (megapixels)
Information about the maximum number of frames per second (fps) supported by the rear camera while recording video at the maximum resolution. Some of the main standard frame rates for recording and playing video are 24 fps, 25 fps, 30 fps, 60 fps.
|24 fps (frames per second)|
Information about additional software and hardware features of the rear camera which improve its overall performance.
Digital image stabilization
Optical image stabilization
White balance settings
Phase detection autofocus (PDAF)
|PureCel Plus-S stacked die technology|
Secondary rear camera - 13 MP (ultra-wide)
Aperture size - f/2.2 (#2)
Third rear camera - 2 MP (depth-sensing)
Sensor model - OmniVision OV02B1B (#3)
Sensor size - 1/5" (#2)
Pixel size - 1.75 μm (#2)
Information about the sensor type of the camera. Some of the most widely used types of image sensors on mobile devices are CMOS, BSI, ISOCELL, etc.
|CMOS BSI (backside illumination)|
Information about the number of pixels on the horizontal and vertical dimensions of the photos taken by the front camera, indicated in megapixels as well.
|21 MP (megapixels)|
Information about the maximum resolution of the videos shot by the front camera.
|1920 x 1080 pixels|
2.07 MP (megapixels)
Digital cameras are able to shoot videos at different frames per second (fps). Some of the main standard frame rates for recording and playing video are 24 fps, 25 fps, 30 fps, 60 fps. Information about the maximum possible fps for shooting videos at the maximum possible resolution.
|30 fps (frames per second)|
Information about additional software and hardware features of the front camera which improve its overall performance.
The loudspeaker is a device, which reproduces various sounds such as ring tones, alarms, music, voice calls, etc. Information about the type of speakers the device uses.
|Dual-microphones for active noise cancellation|
Information whether the device has an FM radio receiver or not.
The tracking/positioning service is provided by various satellite navigation systems, which track the autonomous geo-spatial positioning of the device that supports them. The most common satellite navigation systems are the GPS and the GLONASS. There are also non-satellite technologies for locating mobile devices such as the Enhanced Observed Time Difference, Enhanced 911, GSM Cell ID.
Wi-Fi communication between devices is realized via the IEEE 802.11 standards. Some devices have the possibility to serve as Wi-Fi Hotspots by providing internet access for other nearby devices. Wi-Fi Direct (Wi-Fi P2P) is another useful standard that allows devices to communicate with each other without the need for wireless access point (WAP).
|802.11a (IEEE 802.11a-1999)|
802.11b (IEEE 802.11b-1999)
802.11g (IEEE 802.11g-2003)
802.11n (IEEE 802.11n-2009)
802.11ac (IEEE 802.11ac)
The technology has several versions, which improve the connection speed, range, connectivity and discoverability of the devices. Information about the Bluetooth version of the device.
Bluetooth uses various profiles and protocols related to faster exchange of data, energy saving, better device discoverability, etc. Some of those supported by the device are listed here.
|A2DP (Advanced Audio Distribution Profile)|
LE (Low Energy)
There are several USB connector types: the Standard one, the Mini and Micro connectors, On-The-Go connectors, etc. Type of the USB connector used by the device.
There are several versions of the Universal Serial Bus (USB) standard: USB 1.0 (1996), the USB 2.0 (2000), the USB 3.0 (2008), etc. With each following version the rate of data transfer is increased.
Тhe USB interface in mobile devices may be used for different purposes such as battery charging, using the device as a mass storage, host, etc.
|DisplayPort Alt Mode|
Information whether the device is equipped with a 3.5 mm audio jack.
Information about some of the most widely used connectivity technologies supported by the device.
Information about some of the features and standards supported by the browser of the device.
|Audio file formats/codecs|
List of some of the most common audio file formats and codecs supported standardly by the device.
|AAC (Advanced Audio Coding)|
AMR / AMR-NB / GSM-AMR (Adaptive Multi-Rate, .amr, .3ga)
eAAC+ / aacPlus v2 / HE-AAC v2
FLAC (Free Lossless Audio Codec, .flac)
MP3 (MPEG-2 Audio Layer II, .mp3)
OGG (.ogg, .ogv, .oga, .ogx, .spx, .opus)
WMA (Windows Media Audio, .wma)
WAV (Waveform Audio File Format, .wav, .wave)
|Video file formats/codecs|
List of some of the most common video file formats and codecs supported standardly by the device.
|3GPP (3rd Generation Partnership Project, .3gp)|
AVI (Audio Video Interleaved, .avi)
H.264 / MPEG-4 Part 10 / AVC video
MKV (Matroska Multimedia Container, .mkv .mk3d .mka .mks)
QuickTime (.mov, .qt)
MP4 (MPEG-4 Part 14, .mp4, .m4a, .m4p, .m4b, .m4r, .m4v)
WMV (Windows Media Video, .wmv)
The capacity of a battery shows the maximum charge, which it can store, measured in mili-Ampere hours.
|5000 mAh (milliampere-hours)|
The battery type is determined by its structure and more specifically, by the chemicals used in it. There are different battery types and some of the most commonly used in mobile devices are the lithium-ion (Li-Ion) and the lithium-ion polymer battery (Li-Polymer).
Information about some additional features of the device's battery.
Information about other features of the device.